ReadyMadeRC
900MHZ 200MW TRANSMITTER - INTL VERSION (SPECIAL BUY!)
| CH1 | 910 MHz (Only channel for units shipped to USA or Canada) |
| CH2 | 980 MHz |
| CH3 | 1010 MHz |
| CH4 | 1040 MHz |
| Power requirements | 12V, 200mA |
Frequencies:, Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
INTERNATIONAL VERSION, CANNOT SHIP TO A US ADDRESS UNDER ANY ...ReadyMadeRC
EAGLE TREE - VECTOR FPV CONTROLLER PACKAGE - XT60
| COMPATIBLE | PCM, SPPM and S.BUS |
| FLEXIBLE | fly with or without your FPV equipment |
| REDUCED WIRING | innovative wire harness with power distribution simplifies hookup |
| Virtual SPPM RSSI | some receivers output RSSI and link quality via the SPPM interface, which is supported |
has everything you've dreamed about, in one small, lightweight product:, , In addition to the graphical features shown above, nearly all of the Vector's parameters can be displayed in 3 ways:, , : The Vector can speak flight information to you periodically, or on programmed alarms., Variometers:, The Vector is the first OSD to provide a charting graphical as well as acoustical tone variometers. The variometers are fully programmable to suit your taste., RSSI:, The Vector supports 4 types of RSSI:, , Fast, easy control and menuing system:, The Vector utilizes switch "gestures" and your control stick to let you rapidly scroll through menus and change parameters. All OSD parameters can be configured via the stick menus!, Kitchen sink:, Of course, all the other OSD features you've come to expect from Eagle Tree, such as RADAR, ladders, compass, full 'F16' AHI, flight simulator, manual waypoints, monitoring of up to four battery voltages, and a huge list of parameters available for display are there in the Vector., The Vector system includes the base controller unit, the GPS/Magnetometer, and the Current Sensor/PSU. The Vector's feature list is quite long, so what follows is an overview of the main features:, Full Color OSD, Smooth, razor sharp color graphics:, tired of staring at hard to read white text with clunky graphics? The Vector changes all that. WARNING: a full color OSD can be addictive! :) Colors are fully adjustable to your preference., Numerous flight modes are available, and are easily selectable via one or more switches on your radio:, 2D:, multirotor or fixed wing leveling with or without altitude and heading hold, 3D:, direct rate 3D with or without heading lock, for doing acrobatics when you get bored just flying along. :) Great for holding 3D positio,
The Vector's wiring harness functions perfectly with RMRC camera and ...ReadyMadeRC
EAGLE TREE - VECTOR FPV CONTROLLER PACKAGE - WIRE LEADS
| COMPATIBLE | PCM, SPPM and S.BUS |
| FLEXIBLE | fly with or without your FPV equipment |
| REDUCED WIRING | innovative wire harness with power distribution simplifies hookup |
| Virtual SPPM RSSI | some receivers output RSSI and link quality via the SPPM interface, which is supported |
satellites, in addition to other improvements, which can provide the following benefits:, , has everything you've dreamed about, in one small, lightweight product:, , In addition to the graphical features shown above, nearly all of the Vector's parameters can be displayed in 3 ways:, , : The Vector can speak flight information to you periodically, or on programmed alarms., Variometers:, The Vector is the first OSD to provide a charting graphical as well as acoustical tone variometers. The variometers are fully programmable to suit your taste., RSSI:, The Vector supports 4 types of RSSI:, , Fast, easy control and menuing system:, The Vector utilizes switch "gestures" and your control stick to let you rapidly scroll through menus and change parameters. All OSD parameters can be configured via the stick menus!, Kitchen sink:, Of course, all the other OSD features you've come to expect from Eagle Tree, such as RADAR, ladders, compass, full 'F16' AHI, flight simulator, manual waypoints, monitoring of up to four battery voltages, and a huge list of parameters available for display are there in the Vector., The Vector system includes the base controller unit, the GPS/Magnetometer, and the Current Sensor/PSU. The Vector's feature list is quite long, so what follows is an overview of the main features:, Full Color OSD, Smooth, razor sharp color graphics:, tired of staring at hard to read white text with clunky graphics? The Vector changes all that. WARNING: a full color OSD can be addictive! :) Colors are fully adjustable to your preference., Numerous flight modes are available, and are easily selectable via one or more switches on your radio:, 2D:, multirotor or fixed wing leveling with or without altitude and heading hold, 3D:, direct rate 3D with or without heading lock, ,
Now includes V2 GPS unit! (Requires GPS firmware v1.81 update ...ReadyMadeRC
12.1 INCH RMRC LCD MONITOR
| Image | 12.1" TFT LCD LED |
| Resolution | 800x600 |
| Horizontal frequency range | 30-60KHz |
| Field frequency range | 60-75Hz |
| Brightness | 330cd/m² |
| Viewing Angle | 70°/70°(L/R) 50°/70°U/D |
| Contrast Ratio | 900 |
| Response time | 30ms |
| Input Voltage | DC6-24V |
| Power Consumption | ≦8W |
| Input Signal | VGA,AV1,AV2,Audio,DVI,HDMI |
| Working Temperature | -10℃～50℃ |
| Storage Temperature | -20℃～60℃ |
| Size | 298L×245W×45D mm |
| Weight | 1130g without cables or sun shield, 1330g with cables and sun shield |
| Mounting | Standard 1/4-20 tripod and VESA mounts |
| The 10.1 inch is lighter, brighter and has a higher resolution. But the output of the receiver 4 | 3. Wouldn't i get a much clearer image production on a 4 |
Specifications:, , Display Ratio: 4:3, Package Includes:, , Trying to decide between the 10.1" and 12.1" monitors? See one of our customer's questions below:, Customer, Tim - The biggest difference with the 12.1" monitor is that it is 4:3, so the apparent overall size increase is significant when compared to the others. The image is stretched on the other monitors (with an option to show it in 4:3 which makes the image smaller and wastes some space), but the basic image you'd see on the 10.1" is the same as your 8"...just larger. When it comes to "clearer" image..that's somewhat subjective. Larger images will allow you to see small details better if they are in the video signal, but also will make it more evident that we are working with standard definition video signals. All in all, if I don't have to attach a monitor to my radio and hold the weight with a neck strap or hands, I'd go with the 12.1" first, 10.1" second. However, the finish on the 12.1" screen is a bit better for reducing glare than the 10.1",
Perfect for your FPV ground station, this Ready Made RC ...ReadyMadeRC
EAGLE TREE - VECTOR FPV CONTROLLER PACKAGE - DEANS
| COMPATIBLE | PCM, SPPM and S.BUS |
| FLEXIBLE | fly with or without your FPV equipment |
| REDUCED WIRING | innovative wire harness with power distribution simplifies hookup |
| Virtual SPPM RSSI | some receivers output RSSI and link quality via the SPPM interface, which is supported |
satellites, in addition to other improvements, which can provide the following benefits:, , Years in the making, the Vector has everything you've dreamed about, in one small, lightweight product:, , In addition to the graphical features shown above, nearly all of the Vector's parameters can be displayed in 3 ways:, , : The Vector can speak flight information to you periodically, or on programmed alarms., Variometers:, The Vector is the first OSD to provide a charting graphical as well as acoustical tone variometers. The variometers are fully programmable to suit your taste., RSSI:, The Vector supports 4 types of RSSI:, , Fast, easy control and menuing system:, The Vector utilizes switch "gestures" and your control stick to let you rapidly scroll through menus and change parameters. All OSD parameters can be configured via the stick menus!, Kitchen sink:, Of course, all the other OSD features you've come to expect from Eagle Tree, such as RADAR, ladders, compass, full 'F16' AHI, flight simulator, manual waypoints, monitoring of up to four battery voltages, and a huge list of parameters available for display are there in the Vector., The Vector system includes the base controller unit, the GPS/Magnetometer, and the Current Sensor/PSU. The Vector's feature list is quite long, so what follows is an overview of the main features:, Full Color OSD, Smooth, razor sharp color graphics:, tired of staring at hard to read white text with clunky graphics? The Vector changes all that. WARNING: a full color OSD can be addictive! :) Colors are fully adjustable to your preference., Numerous flight modes are available, and are easily selectable via one or more switches on your radio:, 2D:, multirotor or fixed wing leveling with or without altitude and heading hold, 3D:, direct rate 3,
Now includes V2 GPS unit! (Requires GPS firmware v1.81 update ...ReadyMadeRC
BOSCAM THUNDERBOLT 5.8G 2000MW AV TRANSMITTER
| Power | 2000mW (33dB +-1dB)* |
| Power On Working | Plug and Play |
| Input Voltage | 7-24V DC, 2-6 cells battery |
| Cooling System | whole body heat sink and cooling |
| Channel Switching | channel button and channel display |
| Antenna | RP-SMA female 50 ohm connector |
| Accessories | one original omni antenna, one multi function 5pin cable |
| Size & Weight | 62mm*42mm*20mm, 37g |
| Package Size & Weight | 135mm*85mm*45mm, 82g |
: Amateur Radio Band, 5865M, 5845M, 5825M, 5805M, 5785M, 5765M, 5745M, 5725M;8CH Not frequency-compatible with FatShark, ImmersionRC, Airwave based equipment, of power (including the ones from the other vendors). We take the time to verify the ratings from the manufacturers. Do the other dealers? :) , Notes:, These use reverse polarity, RP-SMA connectors and may require an adapter with the use of some antennas. Although ImmerseionRC A/V connectors fit, the power/ground will need to be reversed before use., Notice:, The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
5.8G Thunderbolt 2000mW* AV wireless transmitter Transmitter frequency They do ...ReadyMadeRC
FR SKY - TARANIS X9D TRANSMITTER, MODE 2 (NO RECEIVER)
Model:, , Operating Temperature Range:, , Operating System:, , Transmitting Frequency:, , System:, , Power Supply:, , Current Drain:, , Operating Humidity:, , Includes:,
FEATURES Quad Ball Bearing Gimbals Receiver Match Audio Speech Outputs ...ReadyMadeRC
FR SKY TARANIS X9D TRANSMITTER MODE 2 PICK YOUR RECEIVER COMBO
Model:, , Operating Temperature Range:, , Operating System:, , Transmitting Frequency:, , System:, , Power Supply:, , Current Drain:, , Operating Humidity:, , Includes:,
Pick your receiver from the list below! FEATURES Quad Ball ...ReadyMadeRC
AIR TITAN KIT (HARDWARE INCLUDED) NO ELECTRONICS
| ATTENTION | According to |
| Wingspan | 2520MM/ 99.2inch |
| Kits Airplane weight | 2.4kg(5.3IB) including all reinforcement parts |
| Extra Payload | 3.0kg-4.0kg (6.6IB-8.8IB)/ flight weight>6.0kg |
| Customized Motor for Airtitan | M60K/ Power 1500W |
| Testing static thrust | 5.5-6.0kg (6S, 15" Prop) |
| Propeller recommend | 15*6 / 15*7 |
| ESC | Advanced 80A OPTO (without Built-in BEC) |
| External UBEC | 5V/6A,5.5V/6A or 6V/6A (Switchable) |
| Material of fuselage and Wing | EPO |
| RMRC 6s batteries found here | 10,000 mAh |
| Main-wing | built- in 4PCS alloy aluminum plus 2PCS carbon tube through the Main-wing |
| Control surface of Aileron and Elevator | carbon tube reinforced, no need further DIY |
Breakdown for Transport:, This plane carries over the “gentle stall” characteristics of the Penguin, but super sized. No scary tip-stalls. Instead, it has super predictable flight characteristics. Tricycle landing gear with a steerable nose gear is included, along with a stable high wing design, plus a bottom camera port, and secondary top camera mounting area. The ARF version includes an 80A OPTO ESC, Massive 1500W motor, a switch mode 5-6V adjustable UBEC, and heavy duty metal geared servos for the ailerons, elevator, and steering. Hand launch is possible, but you might need to work out a bit before you try it (see beginning of video!). Like the Penguin, this airframe was designed with FPV in mind, but would also serve as a great plane to fly at the field if you just want something you can strap a GoPro to, or maybe even 10 of them since it won’t mind the weight. Available and ready to ship now at Ready Made RC, LLC, the best place to get ALL your FPV and RC equipment!, Specifications:, , Customized Brushless Power system:, Servos:, , Battery Recommendations:, , Flight Recomendations:, *Note : 5S with a 15*8 Prop is okay if your flight weight is less than 5.5kg. A 6S pack will however provide “better power", *Note: Flight weight of 5.5kg-6.0kg can meet most FPV requirements, and we recommend less than 6.0kg for most FPV pilots, High Quality Reinforcement :, , Horizontal stabilizer:,
UN1133 shipping regulations, the glue contained in t his product ...ReadyMadeRC
AIR TITAN KIT (HARDWARE INCLUDED) WITH MOTOR, ESC, AND SERVOS
| ATTENTION | According to |
| Wingspan | 2520MM/ 99.2inch |
| Kits Airplane weight | 2.4kg(5.3IB) including all reinforcement parts |
| Extra Payload | 3.0kg-4.0kg (6.6IB-8.8IB)/ flight weight>6.0kg |
| Customized Motor for Airtitan | M60K/ Power 1500W |
| Testing static thrust | 5.5-6.0kg (6S, 15" Prop) |
| Propeller recommend | 15*6 / 15*7 |
| ESC | Advanced 80A OPTO (without Built-in BEC) |
| External UBEC | 5V/6A,5.5V/6A or 6V/6A (Switchable) |
| Material of fuselage and Wing | EPO |
| RMRC 6s batteries found here | 10,000 mAh |
| Main-wing | built- in 4PCS alloy aluminum plus 2PCS carbon tube through the Main-wing |
| Control surface of Aileron and Elevator | carbon tube reinforced, no need further DIY |
Breakdown for Transport:, This plane carries over the “gentle stall” characteristics of the Penguin, but super sized. No scary tip-stalls. Instead, it has super predictable flight characteristics. Tricycle landing gear with a steerable nose gear is included, along with a stable high wing design, plus a bottom camera port, and secondary top camera mounting area. The ARF version includes an 80A OPTO ESC, Massive 1500W motor, a switch mode 5-6V adjustable UBEC, and heavy duty metal geared servos for the ailerons, elevator, and steering. Hand launch is possible, but you might need to work out a bit before you try it (see beginning of video!). Like the Penguin, this airframe was designed with FPV in mind, but would also serve as a great plane to fly at the field if you just want something you can strap a GoPro to, or maybe even 10 of them since it won’t mind the weight. Available and ready to ship now at Ready Made RC, LLC, the best place to get ALL your FPV and RC equipment!, Specifications:, , Customized Brushless Power system:, Servos:, , Battery Recommendations:, , Sample Battery Setup:, , Flight Recomendations:, *Note : 5S with a 15*8 Prop is okay if your flight weight is less than 5.5kg. A 6S pack will however provide “better power", *Note: Flight weight of 5.5kg-6.0kg can meet most FPV requirements, and we recommend less than 6.0kg for most FPV pilots, High Quality Reinforcement :, ,
UN1133 shipping regulations, the glue contained in t his product ...ReadyMadeRC
3DR PIXHAWK
| Weight | 38g (1.31oz) |
| Width | 50mm (1.96") |
| Thickness | 15.5mm (.613") |
| Length | 81.5mm (3.21") |
Note:, Pixhawk is a PPM-input autopilot, which means that it gets RC input from a single cable to the receiver, either via the PPM port, the Futaba S.BUS port, or the special satellite receiver port for Spektrum gear. Most modern RC receivers (and all those sold by 3D Robotics) allow for PPM output, but some, such as non-S.BUS Futaba receivers, do not. If your receiver does not support PPM output, please add a PPM encoder board option to your order below., Pixhawk includes:, , Options:, , Microprocessor:, , Sensors:, , Interfaces:, , Power System:, , Weight and Dimensions:, ,
Pixhawk is an advanced autopilot system designed by the PX4 ...ReadyMadeRC
FAT SHARK DOMINATOR V2 640X480 VIDEO GLASSES
| FOV (field of view) | 35 degrees diagonal |
| Interpupillary (IPD) distance | 57 to 73 mm (adjustable) |
| Optional diopter lens inserts | -2, -4, -6 dpt sold separately |
| Power supply | 7 - 13 V (2S/3S supply) |
| Weight | 200g |
| Record rate | 6Mbps |
Please Note:, To answer many questions about the subject, yes,, Optics:, , Audio:, , User Controls:, , Electrical:, , Power consumption (@7.4V nominal):, 350mA wireless mode, RF Modules (SOLD SEPARATELY):, , Mechanical:, , V2: 640 X 480 VGA, DVR:, , Battery:, , INCLULDED:, 7.4v 1000mAh Fatshark Battery, Includes:,
we have the latest model of Dominator V2's with the ...ReadyMadeRC
FAT SHARK DOMINATOR HD 800X600 VIDEO GLASSES PREORDER!
| FOV (field of view) | 45 degrees diagonal |
| Interpupillary (IPD) distance | 57 to 73 mm (adjustable) |
| Optional diopter lens inserts | -2, -4, -6 dpt sold separately |
| Power supply | 7 - 13 V (2S/3S supply) |
| Weight | 200g |
| Record rate | 6Mbps |
Optics:, , Audio:, , User Controls:, , Electrical:, , Power consumption (@7.4V nominal):, 350mA wireless mode, RF Modules (optional):, , Mechanical:, , HD: 800 X 600 SVGA, DVR:, , Battery:,
NOW AVAILABLE FOR PREORDER! Should be available some time this ...ReadyMadeRC
FR SKY - TARANIS X9D TRANSMITTER, MODE 2 WITHOUT CASE
Model:, , Operating Temperature Range:, , Operating System:, , Transmitting Frequency:, , System:, , Power Supply:, , Current Drain:, , Operating Humidity:, , Includes:,
The same radio, minus the case with a discounted price! ...ReadyMadeRC
EV-PEAK - Q6400AC - 100WX4 AC/DC CHARGER/DISCHARGER
| 3. Accepts all types of R/C batteries | LiPO/LiFe/NiMH/NiCd/Pb. |
| AC Input voltage | 110or220V |
| DC Input voltage | 11-18.0V |
| Charge power max | 100W*4 |
| Discharger power max | 10W*4 |
| Charge current range | 0.1-10.0A |
| Discharge current range | 0.1-2.0A |
| NiCd/NiMH battery cell count | 1 - 15cells |
| LiPo/LiLo/LiFe battery cell count | 1 - 6series |
| Pb battery voltage | 2 V - 20V |
| Dimensions | 243*191*67mm |
| Weight | 1750g |
What makes this charger so good? Here are a few of our reasons:, , Additional Features:, 1. Creates a safe charging condition and minimizes the danger caused by negligence and user setting errors., Specifications:, , Included Accessories:,
The Q6400AC is a beast of a multi-charger and is ...